Hello, I wanted to ask if anyone knew how to contact the people that make the Edrefcard info. I have a Virpil aphla right hand stick and cm03 throttle. and want to use the edrefcard. any help would be awesome thanks.
Discussion Edrefcard.info for Virpil VPC Constellation ALPHA Prime [R] with VPC MongoosT-50CM3 Base and VPC MongoosT-50CM3 Throttle.
- Thread starter Silence002
- Start date
That would be me. The stick is already supported: https://edrefcard.info/device/VPC-ALPHA-Right
Is this the throttle? https://virpil-controls.eu/vpc-mongoost-50cm3-throttle.html
Is this the throttle? https://virpil-controls.eu/vpc-mongoost-50cm3-throttle.html
Yes, I did put all models in the heading of the post.
If I go to https://www.edrefcard.info/ then it takes me refcard, then would go to bindings page then find my binding and Generate Reference car it will show
Unknown controller detected? my old Logitech x56 will show up every time.
Isn't this because the software configuration of the stick produces various GUIDs depending on how you set it up so makes it hard for EDRefCard to determine what it is?
e.g. Mine is seen by Elite bindings as Primary Device="334440CB" and this gives the "unknown controller" message in EDRefCard.
e.g. Mine is seen by Elite bindings as Primary Device="334440CB" and this gives the "unknown controller" message in EDRefCard.
Hi This works for me
VPC Constellation Alpha
VID 03EB
PID 2048
Don't have the throttle yet, which will be next week.
I know that i have to change the PID / VID also to be recognized by edrefcard. Values not known/found yet
As i vaguely remember Virpil change or did these values with every batch. Why? no idea
VPC Constellation Alpha
VID 03EB
PID 2048
Don't have the throttle yet, which will be next week.
I know that i have to change the PID / VID also to be recognized by edrefcard. Values not known/found yet
As i vaguely remember Virpil change or did these values with every batch. Why? no idea
I did try changing VID / PID same concluision. I guess i just make a template by hand on paper. I did see the alpha template thank you ill print that out and input it separately
hello, so I got edref card to work but some of the stuff is not label correctly. the code is (lfsxtl) edrefcard any help would be awesome. also are you making something for the VPC cm-03 throttle
Hi VerticalBlank,
Can we ask nicely for the Virpil VPC MongoosT-50CM3 Throttle 3 on edrefcard, if possible that is?
Found this info on the virpil forum, about changing PID's
https://forum.virpil.com/index.php?...o-update-software-and-firmware/#comment-37198
Thanks anyway the site has been useful for me for years.
AmroBank
Can we ask nicely for the Virpil VPC MongoosT-50CM3 Throttle 3 on edrefcard, if possible that is?
Found this info on the virpil forum, about changing PID's
https://forum.virpil.com/index.php?...o-update-software-and-firmware/#comment-37198
Thanks anyway the site has been useful for me for years.
AmroBank
Sorry for delay, I have a lot on IRL at the moment. For the Virpil VPC MongoosT-50CM3 Throttle 3, can anyone point me to either a blank buttonmap (perhaps from the manufacturer) or an image that we could base a button map upon? It would need to be under a licence that permits both re-use and modification.
As for the VID/PID issue, if the other possible combinations are also unique to the controller in question then I can add them as aliases if you let me know.